SCAT Crankshafts Featured on Chevy Hardcore
A Golen Engine 383-cube Gen-II LT1 built for the street was featured on Chevy Hardcore! This build is running a SCAT Crankshafts 9000 series steel 3.750-inch-stroke crankshaft and a set of 6.000-inch forged 4340 I-beam rods, which were upgraded with ARP rod bolts. Despite the popularity of the Gen 1 SBC, LS platform and the direct-injected LT1 platform, Golen Engine is still working hard on...
read more
SCAT Attending AERA Conference
SCAT Enterprises will be at the upcoming AERA Tech & Skills Regional Conference at Liberty Engine Parts in Pennsauken, New Jersey, on Saturday, September 14! You don’t need to be an AERA member to attend this conference, and all shops are welcome to attend. All attendees will receive a free Failure Analysis Manual as well as door prizes from several vendors. SCAT’s very own Tom...
read more
Procar by SCAT Testimonial
Tim Moreland of Graham, Texas, shared his ’66 Chevy C10 Pickup that has Procar by SCAT seats (and material) AND a SCAT Crankshafts crank! From Tim: “I sure love my Procar seats. I built my own console, and I called the guys at Procar and they sold me the material to match my seats and enough to do the door panels also. The price of the seats and material was very reasonable. Thank...
read more
Procar by SCAT Seats Used in Four Wheeler Week to Wheelin’ Build
Procar by SCAT Pro-90 Lowback seats were recently used in Four Wheeler’s Week to Wheelin Bronco build! This build was completely made from the ground up — nothing like this build was even in existence — and we were ecstatic to be a part of it. Take a look at some photos of the seats before and after they were in the build, as well as the final product: To check out all the...
read more
Original Parts Group Chevy Car Show
The Original Parts Group Chevy Car Show (Pre-1988) is coming up on Saturday, June 8! This is open to all Chevy models that are pre-1988, but registration is limited to 200 vehicles.
read more
Tips for Installing Procar by SCAT Seats
Jeff Honeycutt of Car Craft Magazine is sharing tips on installing your Procar by SCAT...
read more
SCAT Crankshafts Featured in Engine Builder Magazine
Engine Builder Magazine recently featured a ZSR Engines build as their Engine of the Week! This 438 cid N/A small block Ford engine is running a SCAT 4.100″ stroke crankshaft. ‘We used a Dart block and did all of our normal machining to it – square checking, boring, a torque plate hone, and a line hone,’ Zach Smith, owner of ZSR Engines, says. ‘For the rotating...
read more
SCAT Excalibur Lightweight Crankshaft Featured on EngineLabs
The new SCAT Excalibur Lightweight Crankshaft, weighing in at just under 50 pounds, was recently featured on EngineLabs. Lightweight rotating assemblies are the key to a high-revving small block and allow vehicles to reach their ideal power band quicker. Read more about the details of our new crankshaft: Forged from 4340 steel, the cranks are precision-ground, heat-treated, and nitride-hardened...
read more
Procar by SCAT Featured in Super Chevy Magazine
Eddie’s 1964 Chevy Corvette Convertible with Procar by SCAT Rally XL seats was recently featured in Super Chevy Magazine! Being that this Corvette is a convertible, the interior is practically as noticeable—and thus important—as the exterior of the vehicle. To start things off, Roberts installed Procar 1000 Series seats covered in Bloodhound Red leather from Relicate. The rest of the...
read more
2019 Dix Performance North Trade Show Recap
We were honored to sponsor the 2019 Dix Performance North Trade Show last month in San Pedro, CA! We had the opportunity to show Dix’s VIP customers around the SCAT Enterprises factory and talk shop with them. Take a look at the recap video...
read more